Seco/Warwick furnace to process Jet Engine components

Seco/Warwick, Meadville, PA, has developed a system to perform clean brazing processes in high vacuum as efficiently as possible, ensuring the highest protection of the treated part surfaces. The solution will be used to process jet engine components.

The German Partner carries out comprehensive repairs of technologically advanced jet engines. The company also has a research center which develops innovative repair techniques for various types of components and entire engines. The group employs several thousand qualified employees in various locations around the world and is a leader among companies repairing and providing full service MRO for jet engines. The purchase of a vertical vacuum furnace will improve production processes and significantly increase the commercial heat treater’s efficiency.

Read further here.

Lindberg ships full muffle mesh belt conveyor furnace to manufacturing industry

Lindberg/MPH, Mich,  a leading manufacturer of heat treat furnaces, announced the shipment of a continuous full muffle mesh belt conveyor furnace to an industrial manufacturer.

This conveyor furnace is designed for applications with a nitrogen atmosphere and a maximum temperature of 1,100°C. Additionally, the furnace has a hydrogen flow meter and combustible gas system so the customer can run a hydrogen atmosphere when needed. The combustible gas system provides a timed nitrogen gas purge of the muffle before process gas can be introduced into the furnace muffle. The conveyor furnace has overall dimensions of 128” L x 22” W 41.5” H. There are tables at both ends of the furnace for loading and unloading of the product. The unit is designed with four (4) temperature zones and a water-cooling section that parts travel through prior to exiting the chamber.

Read further here

One Minute Mentor: Salt Bath Furnaces

The salt bath method of hardening is predominant with high-speed steel tools. With correct operating conditions, tools can be heat treated without carburization, decarburization, and scaling. The surface will be fully hard with a minimum of distortion. The four types of salt baths generally used are preheating baths, high-temperature baths, quenching baths, and tempering baths.

Molten salts of various compositions are well adapted to all operations in the heat treatment of tool steels. For tools that cannot be ground after hardening or for tools that require an excellent surface condition and the maintenance of sharp edges, salt bath heating provides excellent results. These salt baths contain different compositions of BaCl2, NaCl2, and KCl as well as additional additives to avoid decarburization. The higher the working temperature, the higher the content of BaCl2 usually is. Higher additions of CaCl2 are typically used in salt baths for the quenching step.

For more information, click on the link below (subscription required). Then scroll to Figure 2.

R Schneider; R. Mesquita; W Schützenhöfer, Distortion in Tool Steels, ASM International, 2014, https://doi.org/10.31399/asm.hb.v04d.a0005958

Special fasteners to be processed in a Seco/Warwick vacuum furnace

Seco/Warwick, Meadville, Pa., will deliver a  Vector vacuum furnace to a plant producing highly advanced fasteners for the largest manufacturers in the aerospace industry. 

The machine will process self-locking nuts, nut plates, barrel nuts, stud nuts, spline nuts, clamp nuts, as well as a wide range of washers and flanges. The Italian Partner is an innovator in the field of comprehensive fastening solutions. The Vector furnace will become part of a modern production plant, increasing not only its efficiency, but also guaranteeing thermally treated fasteners of the highest quality.

The furnace on order is a standard solution perfectly suited to aviation industry needs. Thanks to a very refined design without any additional modifications, the furnace will perform at high operating temperatures, up to 1300°C.

The furnace on order is equipped with a dew point sensor for each of the gases. It is a system solving one of heat treatment’s very critical requirements, which is to control the quality/purity of the gas used during the process. Vector also features a partial pressure control system which helps prevent evaporation and sublimation of alloying elements from the load surface during the vacuum heat treatment.

Read further here.

Wisconsin Oven ships curing conveyor oven to aerospace industry

Wisconsin Oven Corporation, East Troy, Wis., has announced the shipment of one belt conveyor oven that will be used for curing polystyrene on aluminum parts for the aerospace industry.

This industrial conveyor oven has a maximum temperature rating of 300° F and interior chamber dimensions of 5’4” W x 8’4” L x 6” H. The recirculation system is designed with a top-down airflow configuration and utilizes a 10,000 CFM @ 10 HP blower. Guaranteed temperature uniformity of ±10° F at 210° F was documented with a temperature uniformity test.

The conveyor system is a continuous belt style and utilizes an Allen-Bradley variable frequency drive that allows for speed adjustments. A digital screen on the control panel door displays the conveyor speed during operation. The oven temperature and conveyor speed are controlled by a Watlow F4T digital controller located on the control panel door with PID control and adaptive turning.

Read further here.

Lindberg/MPH ships rod overbend box furnace to the manufacturing industry

Lindberg/MPH, Mich., has announced the shipment of a rod overbend box furnace with powered load/unload table to the manufacturing industry. This heat-treating furnace has a maximum temperature rating of 2000°F and a load capacity of 900 lbs. 

The workspace dimensions of the furnace are 24” W x 36” D x 18” H and it is designed for air atmosphere applications. The box furnace features an automated actuator to flip the push/pull mechanism on the load table to eliminate the operators need to manually flip it into push position. This option allows the push/pull head to retract from the furnace once the work grid is in the furnace chamber and increase operator safety by removing the need to reach into the hot furnace with a hook to flip the push/pull head and.

The furnace chamber is heated with a radiant heating system the utilizes heavy gauge alloy rod over-bend heating elements mounted along the side-walls and the floor. The furnace temperature is controlled by an Allen Bradley ControlLogix Programmable Logic Controller that includes digital setpoint and display. A Honeywell DC2500 high limit controller disconnects the power to the heating elements and sounds an audible alarm if the temperature exceeds desired set-point. 

Read further here