Solar Atmospheres expands California operations with new 10-bar vacuum furnace

Solar Atmospheres, Fontana, California, announced the installation and commissioning of a new 10-bar vacuum furnace at its California facility. Manufactured by sister company Solar Manufacturing, the horizontal furnace features a hot zone measuring 48-in. wide by 48-in. high by 96-in. deep, with a maximum load capacity of 12,000 pounds and an ultimate vacuum level of 1×10⁻⁶ Torr. The furnace expands the facility’s high-pressure quenching capabilities for processing titanium and high-performance alloys serving the aerospace, defense, medical, and power generation markets. “This investment gives our customers another regional solution for high-pressure quenching of large components and heavy workloads,” said Derek Dennis, President of Solar Atmospheres California.

Read further here

Ipsen supports Siemens AG with modernization of high-vacuum furnaces for energy infrastructure expansion

Ipsen, Cherry Valley, Ill., announced that it has successfully modernized its VHFC high-vacuum furnaces for Siemens AG, marking a significant milestone in their shared mission to enhance sustainability and efficiency in energy infrastructure. The project supports Siemens’ strategic efforts to expand medium and high-voltage grids globally, a key component of the energy transition and the broader push for electrification.

As part of this initiative, Ipsen is delivering three new VHFC-1000x1200x1000 (HV) high-vacuum brazing systems to Siemens’ production facilities in Goa, India, and Wuxi, China. The Goa facility will receive two systems, while the Wuxi facility will add one. All systems are manufactured in Germany and are critical to the production of vacuum interrupters, which are core components of switchgears used in power distribution networks.

These vacuum brazing systems play a pivotal role in enabling the switch from gas-insulated disconnectors to vacuum interrupters, effectively eliminating the use of fluorinated gases. This shift significantly reduces greenhouse gas emissions, aligning with global environmental protection goals.

Ipsen’s collaboration with Siemens reflects their joint commitment to supporting the expansion of renewable energy and sustainable energy infrastructure worldwide. The increased production capacity provided by these systems underscores the importance of advanced technology in achieving energy efficiency and reducing environmental impact.

Read further here.

Evolution on the microstructure and mechanical properties of a new multicomponent near-Alpha Titanium Alloy after rolling and heat treatments

Beijing University of Technology, China, presented the microstructure and mechanical properties of a new type of multi-component near-α titanium alloy sheet after rolling, 700°C aging, and 800°C aging in a new paper.

 The results show that the strength of the alloy after aging at 700°C increases from 1156 MPa to 1304 MPa, respectively, but decreases to 1246 MPa with the aging temperature increasing. The ductility of the alloy aged at 700°C is lower than that of the rolled state, but the ductility increases slightly with the aging temperature increasing. The effect of aging heat treatment on the microstructure and precipitation behavior of alloy plates has been studied and compared with alloys before aging. 

After heat treatment, the content of primary α decreases from 25% to 5%, respectively. Two kinds of silicide precipitate at different positions, with the large-size spherical silicide being (Ti, Zr, Nb)5Si3, and the small-size fusiform silicide being (Ti, Zr, Nb)6Si3, respectively. Ti3Al was precipitated in the primary α phase, during the aging process. The silicides exhibit the strengthening effect on the alloy, but the effect weakens when the silicides grow up. The loss in ductility is mainly attributed to the precipitation of the α2 phase after aging treatment. However, ductility is improved after applying higher aging temperatures as the size of the α2 phase becomes smaller, and the distribution of them tends to become dispersed.

Read further here

 

Can Copper Help Fight COVID-19?

Experts in the fields of metallurgy and microbiology say that copper can be a powerful weapon in the current fight against COVID-19. They believe it can also help curtail future pandemics if utilized properly. In this digital-first article from Advanced Materials & Processes, ASM International’s flagship magazine, the authors recommend the expanded use of copper alloys in public spaces to reduce the spread of COVID-19 and other infectious diseases.

Continue reading

United States Steel to invest a billion dollars in new plant

United States Steel Corp., Pittsburgh, announces that it will invest more than $1 billion to construct a new sustainable endless casting and rolling facility at its Edgar Thomson Plant in Braddock, Pa., and a cogeneration facility at its Clairton Plant in Clairton, Pa., both part of the company’s Mon Valley Works.

Continue reading