Web Content Filters

Filters Applied

No filters

Refine Results

Keyword(s)

MATERIALS RESOURCES

Introduction to Metallurgical Lab Practices, December 9 - 11, 2019

December 09, 2019 - December 11, 2019
Novelty, OH, 44072, United States
Instructor: Mr. John Peppler

Basic techniques commonly used in a Metallurgical Laboratory will be taught in this class. You will become familiar with metallography by sectioning, mounting, grinding, polishing and etching samples. These samples will be examined and photomicrographs obtained by using optical microscopes equipped with digital cameras. Various Microhardness and Macrohardness equipment will be used to demonstrate the strengths and limitations of the tests. Tensile Testing and Impact Testing will be performed on standard samples. Basic principles and sample demonstration on the use of Scanning Electron Microscopy (SEM) will be covered. Hands on testing complimented by lectures on the basics of the tests will give a thorough overview of these procedures. This is the course you need if you learn by doing and could use an overview of Metallographic Lab procedures.

Learning & Professional Development / Courses / Classroom

Mechanical Testing of Metals, December 2-5, 2019

December 02, 2019 - December 05, 2019
Novelty, OH, 44073-0002, USA
Instructor: Mr. William L. Mankins, FASM

This is a hands-on introduction to standard mechanical testing and the properties derived from those tests, together with a discussion of testing philosophy to determine suitability for service and suitability for manufacture. Standardized testing procedures (ASTM, SAE, AWWA, etc.) are discussed, including limitations of a test, why specific requirements are present in the test procedure, and interpretation of experimental results. There is discussion of how metallurgical variables can affect test results, and how microstructure can affect selection of a given testing procedure. (For example, hardness testing of wrought vs. cast material.) This course is taught at a level that requires some algebraic manipulation as well as the use of logarithms. Students are required to bring a scientific calculator.

Learning & Professional Development / Courses / Classroom

Metallurgy for the Non-Metallurgist®, December 2-5, 2019

December 02, 2019 - December 05, 2019
Novelty, OH, 44073-0002, USA
Instructor: Dr. McIntyre. R. Louthan, Jr., PhD, FASM

Metals and alloys are used in the greatest variety of applications of all engineering materials and drive your products success. That is why it's crucial to have knowledge about what metals are, how they behave, and why they behave differently than ceramics, glass, and plastics. This course will provide you with essential knowledge about metallurgy and how to apply it your business or industry.

Learning & Professional Development / Courses / Classroom

Metallurgy of Steel for the Non-Metallurgist, November 18-20, 2019

November 18, 2019 - November 20, 2019
Novelty, OH, 44073-0002, USA
Instructor: Dr. Robert L. Freed, PhD, FASM

Steel is, technologically and economically, the most important of all materials. Understanding the metallurgy involved in making steel, in shaping it by hot or cold processes, in welding it, and in heat-treating it to develop any of the extraordinarily diverse combinations of strength, hardness, toughness, and ductility available is essential to successful manufacturing and construction. This course teaches the basics and delves into some of the more advanced topics critical to steel fabrication.

Learning & Professional Development / Courses / Classroom

Metallurgy of Welding and Joining, November 18-21, 2019

November 18, 2019 - November 21, 2019
Novelty, OH, 44073-0002, USA
Instructor: Dr. Robert W. Messler, Jr., PhD, FASM

Welding metallurgy is a complex subject because it requires knowledge of materials, welding processes, design, and inspection. Metallurgy of Welding and Joining provides an excellent review of welding processes, welding of materials ranging from carbon steel to specialized alloys, guidelines for designing weldments to facilitate welding, and testing and inspecting welds to meet performance requirements. To measure your retention of each lesson's materials and end-of -lesson test will be provided, in addition to an end of course examination.

Learning & Professional Development / Courses / Classroom

Advanced Metallographic Techniques, November 18-21, 2019

November 18, 2019 - November 21, 2019
Novelty, OH, 44073-0002, USA
Instructor: Mr. Natalio T. (Nat) Saenz, FASM

Learn basic and advanced metallographic techniques that will reveal the true microstructural characteristics of a wide range of materials.  The theory and understanding of the proper selection of abrasives, lubricants, equipment, polishing cloths/pads and a basic understanding of chemomechanical polishing will be discussed. The course covers the preparation methods of most metals and alloys, composites, hard metals, ceramics and coatings.

Learning & Professional Development / Courses / Classroom

HT, Microstructures and Performance Carbon and Alloy Steels, November 18-20, 2019

November 18, 2019 - November 20, 2019
Novelty, OH, 44073-0002, USA
Instructor: Dr. Dana Medlin, PhD

Heat treated bar and forging steels remain the major material for parts (such as shafts, gears, bearing, fasteners, oil country tubulars, aircraft landing gear, tools of all sorts, and many other applications) manufactured for demanding applications that require high or ultra-high strength, high fatigue resistance, and /or high wear resistance, all combined with good levels of toughness and fracture resistance. This course will review the phases that form in carbon and alloy steels and the modifications produced in the iron-carbon diagram by alloying and manufacture. Microstructures and the phase transformations by which they are produced in all phases of manufacture, from casting through quench and tempering, will be described and related to mechanical properties and performance, including fracture and potential embrittlement phenomena.

Learning & Professional Development / Courses / Classroom

Heat Treating Furnaces and Equipment, November 14-15, 2019

November 14, 2019 - November 15, 2019
Novelty, OH, 44073-0002, USA
Instructor: Mr. William M. Andreski

Heat treating is key to most manufacturing process, so the equipment used is just as important as the process itself. This course provides an overview of essential aspects associated with various furnace units used to heat treat metallic parts. For your benefit, the course will take place in the classroom as well as two guided factory tours. This will give you an inside view of the world of heat treating furnaces and equipment.

Learning & Professional Development / Courses / Classroom

Basics of Heat Treating, November 11-13, 2019

November 11, 2019 - November 13, 2019
Novelty, OH, 44073-0002, USA
Instructor: Mr. William M. Andreski

Heat treating is considered the least understood, but most integral part of the manufacturing processes. An efficient heat treating process reduces the overall manufacturing costs associated with energy use, scrap, re-work, and quality issues. Heat treating is critical for your business and industry.

Learning & Professional Development / Courses / Classroom

Metallographic Techniques, November 11-14, 2019

November 11, 2019 - November 14, 2019
Novelty, OH, 44073-0002, USA
Instructor: Mr. Natalio T. (Nat) Saenz, FASM

During this course, participants receive intensive instruction and assistance in learning the principles of metallography. Manual preparation, automatic preparation, and hands-on activities, such as preparing a variety of hard, soft, ferrous, and non-ferrous alloys, are used to demonstrate many metallographic techniques.

Learning & Professional Development / Courses / Classroom

ASM Affiliate Societies