Intel Corporation, Santa Clara, Calif., devised a process to manufacture, test, and demonstrate positive performance results with its new backside power solution called PowerVia, enabling chipmaking to go two-sided for the first time.
Continue readingSolar Atmospheres of California adds Airbus approval
Solar Atmospheres, Fontana, Calif., has announced that they are now Airbus approved for heat treating.
Frank Trujillo, director of Sales for Solar Atmospheres of California, stated that, “Many Airbus suppliers were in need of a heat treater in the West that could process parts, plates and bars in support of increased Airbus production rates. SCA is proud to be a partner on the Airbus Team!”
With our wide range of furnaces, we are capable of processing very small pieces or loads of 50,000 pounds and up to 24 feet in length. This approval will translate into improved lead-times and greater efficiencies for all Airbus suppliers that require heat treat services in the Western Region.
Nitrex installs nitriding system at Akademi Metalurji
Nitrex Vacuum, Quebec, has installed a turnkey nitriding system at Akademi Metalurji, a full-service commercial heat-treating solutions provider located in Turkey. The project includes a mid-sized pit-type furnace, advanced controls, three process technologies along with accelerated cooling.
The decision to invest in a new nitriding system was driven by the company’s objective to overcome efficiency and quality challenges faced with their previous furnace at the Gebze facility. The prior system consumed excessive amounts of process gases and yielded inconsistent nitriding results. With the addition of a Nitrex NX-1015 pit furnace, Akademi Metalurji can now save on process gases and production time, while also expanding their heat treatment capabilities to accommodate wider-dimensioned parts. The nitriding furnace offers an effective work zone of 39” diameter by 59” high (1000 x 1500 mm) and can handle a load of up to 4400 lbs. (2000 kg). The supplied library of Nitreg-based recipes is tailored to meet different application requirements, resulting in a hardened surface that is highly wear-resistant. For applications like machinery components, tooling, dies, and molds, where Akademi Metalurji specializes, Nitreg delivers improved tooling performance, ensuring longer service life and higher throughput. Ultimately, this leads to tool cost savings for their customers.
The system was successfully installed at the Gebze facility, located southeast of Istanbul, and commenced operations in April 2023. Since then, it has been running smoothly, delivering excellent results.
Hardide Coatings partners with Gardner Aerospace to coat Airbus components
Hardide Coatings, UK, has entered into a partnership with Gardner Aerospace, UK, to coat key wing components for the Airbus A320 family of aircraft.
Continue readingTesting coatings for corrosion protection
To shield steel from the corrosive threats posed by sea air, Sandia National Laboratories researchers tested a variety of nickel mixtures as protective coatings on stainless steel. The researchers found that the specific material applied, and the specific application process used, impacted the properties of the coating, including how protective it was against corrosion.
Continue readingA new process for microprinting within existing materials
Scientists have questioned how to manufacture microdevices that cannot be produced using layering and whether it is conceivable to directly print inside a pre-existing three-dimensional material.
Continue readingCorrosion control by self-healing epoxy coatings
Scientists at the Instituto de Ciencia y Tecnologia de Polimeros (ICTP) and Centro Nacional de Investigaciones Metalurgicas (CENIM), Spain, studied corrosion control by autonomous self-healing epoxy coatings based on superabsorbent healing agents.
Continue readingNew superconducting materials make their debut
By exploring the many possible combinations of elements, physicists hope to find new superconductors that work at lower pressures and higher temperatures than the hydrides studied so far.
Continue readingNew robot boosts solar energy research
Researchers at North Carolina State University, Raleigh, N.C., have created a robot called RoboMapper that can rapidly identify new perovskite materials with improved stability and solar cell efficiency and is capable of conducting experiments more efficiently and sustainably to develop a range of new semiconductor materials with desirable attributes.
Continue readingZentropy and the art of creating new ferroelectric materials
Systems in the Universe trend toward disorder, with only applied energy keeping the chaos at bay. The concept is called entropy, and examples can be found everywhere: ice melting, campfire burning, water boiling. Zentropy theory, however, adds another level to the mix.
Continue readingPlumbing the depths of thermoelectrics in search of novel materials
In the search for thermoelectric materials with the best possible properties, a research team at the Vienna University of Technology (TU Wien) investigated various metallic alloys.
Continue readingTuning a fundamental material property with an electronic coating
Researchers at the University of Southern California have developed a bilayer coating of an insulator and graphene on top of a semiconductor that can tune the energy required to eject electrons out of the material, potentially making electrochemical devices more efficient.
Continue readingAccelerating sustainable semiconductors with ‘multielement ink’
Developed by researchers from Lawrence Berkeley National Laboratory (Berkeley Lab) and UC Berkeley, a new semiconducting material called “multielement ink” is the first “high-entropy” semiconductor that can be processed at low or room temperature, making the semiconductor purification and development process significantly less heat-intensive and more sustainable.
Continue readingNovel self-driving microscopy technique to speed up data collection
Scientists combined artificial intelligence and microscopy to accelerate data collection and protect sample integrity.
Continue readingHitachi High-Tech Group introduces NEXTA DMA200 Thermal Analyzer with high force capability and enhanced efficiency
Hitachi High-Tech Science Corporation, Japan, launched a new product in the NEXTA series, the DMA200 a dynamic mechanical analyzer for advanced materials development and product quality control.
Continue readingNext generation semiconductors: diamond device shows highest breakdown voltage
Researchers at the University of Illinois Urbana-Champaign have developed a semiconductor device made using diamond, that has the highest breakdown voltage and lowest leakage current compared to previously reported diamond devices.
Continue readingUSTC achieves chemically controlled reversible magnetic phase transition
A research team at the University of Science and Technology of China of the Chinese Academy of Sciences developed a groundbreaking chemical method for two-dimensional metal-organic lattices.
Continue readingOnsemi opens state-of-the-art systems application lab for electric vehicles in Europe
Onsemi, Scottsdale, Ariz., opened an application test lab in Piestany, Slovakia, focused on the advancement of system solutions for battery/plug-in hybrid/electric vehicles and energy infrastructure power conversion systems.
Continue readingWeebit Nano’s ReRAM IP Achieves high temperature qualification in SkyWater Technology’s S130 Process
Weebit Nano Limited, Israel, a leading developer of advanced memory technologies for the global semiconductor industry, and SkyWater Technology, Bloomington, Minn., the trusted technology realization partner, announced that Weebit’s Resistive Random-Access Memory IP module has been fully qualified in SkyWater’s 130nm CMOS process at temperatures of up to 125 degrees Celsius – the temperature specified for Grade-1 automotive applications.
Continue readingOxford Instruments launched its Innovation Center
Oxford Instruments, England, has brought together the best of its analytical innovations to form the Oxford Instruments Innovation Center, a state-of-the-art facility at its High Wycombe site.
Continue readingIs graphene the best heat conductor? Researchers investigate with four-phonon scattering
Graphene, a material that consists of a single layer of carbon atoms, has been celebrated by many as the “next big thing” in material science. However, according to Purdue University researchers, its thermal properties may not be as revolutionary as previously thought.
“Graphene is the first two-dimensional material that human beings ever created,” said Xiulin Ruan, professor of mechanical engineering. “It’s basically a layer of carbon, one atom thick. It was first discovered in 2004 and won the Nobel Prize for Physics in 2010. Ever since then, it’s been studied by many researchers because of its unique properties.”
For example, graphene is said to conduct electricity better than any other material known to science and is known for its material strength. Thermal transport researchers were also quick to give it the title of best heat conductor.
“Previously, the material thought to have the highest thermal conductivity was diamond,” said Zherui Han, a Ph.D. student in Ruan’s lab. “That’s the material that can transfer the most heat the quickest. But when graphene came out, mainstream studies showed it to be much better than diamond.”
Thermal conductivity is measured in watts per meter per Kelvin. On this scale, a diamond’s thermal conductivity is generally understood to be about 2,000. But when scientists started measuring graphene’s thermal conductivity, early estimates reached above 5,000. Obviously, this caught the interest of scientists like Ruan, whose research focuses on heat transfer.
“However, subsequent experimental measurements and modeling have refined graphene’s thermal conductivity,” Ruan said. “More recent papers brought the number to around 3,000, which is still quite better than diamond. But we found something altogether different.”
Ruan’s team has predicted the thermal conductivity of graphene at room temperature to be 1,300 W/(m K)—not only less than diamond but also less than the raw graphite material that graphene is made from.
The disparity between their work and previous work comes down to a phenomenon called four-phonon scattering. Phonons are how heat transfer scientists describe the movement of heat in solids on a quantum-mechanical level. Until recently, researchers could only understand three-phonon scattering to predict the transfer of heat through solids.
But in 2016, Ruan’s team developed a general theory of four-phonon scattering, and a year later they successfully quantified four-phonon scattering. This led to Ruan receiving the highest honor from the International Phononics Society in 2023.
So, how does this relate to graphene? “Graphene is a two-dimensional material of only one atom thick,” Han said.
“Previous studies suggest that three-phonon scattering would be restricted by this two-dimensionality, which in theory makes graphene much more thermally conductive than bulk materials. But four-phonon scattering is not restricted by the 2D nature of graphene; in fact, the effect is quite strong. Our work has shown that four-phonon scattering becomes the leading scattering channel in graphene over three-phonon scattering. This is a striking result.”
One barrier to this discovery was the availability of raw computing power. Calculating this four-phonon scattering required a parallel computing strategy, essentially utilizing a computing cluster with one terabyte of memory. This was accomplished at the Rosen Center for Advanced Computing at Purdue University.
At the moment, these calculations are all theoretical. The team works with Prof. Li Shi at the University of Texas at Austin, supported by their collaborative National Science Foundation grants, to verify the findings experimentally. Previous measurements on graphene have had large error bars, which need to be reduced to verify their theory. They also plan to predict the thermal conductivity of graphene of multiple layers of atoms, rather than just one.
“Without experimental validations as yet, we know the community will be skeptical about this very non-mainstream prediction,” Ruan said.
“I always say exceptions are how science moves forward,” Ruan said. “We are cautiously optimistic about our findings. With four-phonon scattering, it’s our hope to deliver much more accurate theoretical assessments of these materials in the future.”
For more information: Physical Review B
Image: Spectral and mode contribution. (a) Spectral contributions to κ of graphene at room temperature without boundary scattering. The inset shows the cumulative thermal conductivity as a function of phonon frequency. (b) ZA phonons’ contribution to κ and its percentage at room temperature, and comparison to first principles at 3ph (renorm. stands for phonon renormalization that was not included before) [9] and MD work [29]. In both plots, the 3ph case presented here is calculated at N=180 without boundary scattering, and note that it is not converged with N.
Materials scientist wins award for improving the reliability of electrical contacts in cars
Materials scientist Frank Mücklich, Professor of Functional Materials at Saarland University, Germany, has developed a laser surface texturing procedure that makes the surfaces of electrical contacts more stable and more efficient.
Continue readingThermo Fisher Scientific announces new electron beam fault localization system for analyzing advanced logic semiconductors
Thermo Fisher Scientific, Hillsboro, Ore., the world leader in serving science, introduced the Thermo Scientific Meridian EX System— an electron-beam-based failure analysis solution designed to enable precise fault localization on advanced semiconductor logic technologies that helps users localize defects within complex power networks and achieve 10X improvement in spatial resolution compared to optical fault isolation solutions.
Continue readingUnited Safety launches new lithium-ion battery failure detection sensor
United Safety & Survivability Corporation, Exton, Pa., a global leader in advanced safety solutions, launched its latest innovation, a groundbreaking lithium-ion battery failure detection sensor that could help prevent electric vehicle fires before they happen and sets a new standard in safety for electric vehicles across industries.
Continue readingAutonomous lab discovers best-in-class quantum dot in hours that would have taken humans years
While it can take years of focused laboratory work to determine how to make the highest quality materials for use in electronic and photonic device applications, researchers at North Carolina State University developed an autonomous system that can identify how to synthesize “best-in-class” materials in hours or days.
Continue readingMIT physicists turn pencil lead into “gold”
MIT physicists have metaphorically turned graphite, or pencil lead, into gold by isolating five ultrathin flakes stacked in a specific order. The resulting material can then be tuned to exhibit three important properties never before seen in natural graphite.
“It is kind of like one-stop shopping,” says Long Ju, an assistant professor in the Department of Physics and leader of the work. “Nature has plenty of surprises. In this case, we never realized that all of these interesting things are embedded in graphite.”
Further, he says, “It is very rare material to find materials that can host this many properties.”
Graphite is composed of graphene, which is a single layer of carbon atoms arranged in hexagons resembling a honeycomb structure. Graphene, in turn, has been the focus of intense research since it was first isolated about 20 years ago. More recently, about five years ago, researchers including a team at MIT discovered that stacking individual sheets of graphene and twisting them at a slight angle to each other, can impart new properties to the material, from superconductivity to magnetism. The field of “twistronics” was born.
In the current work, “we discovered interesting properties with no twisting at all,” says Ju, who is also affiliated with the Materials Research Laboratory.
He and colleagues discovered that five layers of graphene arranged in a certain order allow the electrons moving around inside the material to talk with each other. That phenomenon, known as electron correlation, “is the magic that makes all of these new properties possible,” Ju says.
Bulk graphite — and even single sheets of graphene — are good electrical conductors, but that’s it. The material Ju and colleagues isolated, which they call pentalayer rhombohedral stacked graphene, becomes much more than the sum of its parts.
Key to isolating the material was a novel microscope Ju built at MIT in 2021 that can quickly and relatively inexpensively determine a variety of important characteristics of a material at the nanoscale. Pentalayer rhombohedral stacked graphene is only a few billionths of a meter thick.
Scientists including Ju were looking for multilayer graphene that was stacked in a very precise order, known as rhombohedral stacking. Says Ju, “there are more than 10 possible stacking orders when you go to five layers. Rhombohedral is just one of them.” The microscope Ju built, known as Scattering-type Scanning Nearfield Optical Microscopy, or s-SNOM, allowed the scientists to identify and isolate only the pentalayers in the rhombohedral stacking order they were interested in.
From there, the team attached electrodes to a tiny sandwich composed of boron nitride “bread” that protects the delicate “meat” of pentalayer rhombohedral stacked graphene. The electrodes allowed them to tune the system with different voltages, or amounts of electricity. The result: They discovered the emergence of three different phenomena depending on the number of electrons flooding the system.
“We found that the material could be insulating, magnetic, or topological,” Ju says. The latter is somewhat related to both conductors and insulators. Essentially, Ju explains, a topological material allows the unimpeded movement of electrons around the edges of a material, but not through the middle. The electrons are traveling in one direction along a “highway” at the edge of the material separated by a median that makes up the center of the material. So the edge of a topological material is a perfect conductor, while the center is an insulator.
“Our work establishes rhombohedral stacked multilayer graphene as a highly tunable platform to study these new possibilities of strongly correlated and topological physics,” Ju and his coauthors conclude.
For more information: Nature Nanotechnology
450-million-year-old organism finds new life in softbotics
Researchers from Carnegie Mellon University’s Department of Mechanical Engineering, along with paleontologists from Spain and Poland, have utilized fossil records to create a soft robotic model of Pleurocystitid. This marine organism, which lived about 450 million years ago, is thought to be among the earliest echinoderms that could move using a muscular stem.
The research seeks to broaden the modern perspective of animal design and movement by introducing a new field of study – Paleobionics – aimed at using Softbotics, robotics with flexible electronics and soft materials, to understand the biomechanical factors that drove evolution using extinct organisms.
“Softbotics is another approach to inform science using soft materials to construct flexible robot limbs and appendages. Many fundamental principles of biology and nature can only fully be explained if we look back at the evolutionary timeline of how animals evolved. We are building robot analogs to study how locomotion has changed,” said Carmel Majidi, lead author and Professor of Mechanical Engineering at Carnegie Mellon University.
With humans’ time on earth representing only 0.007% of the planet’s history, the modern-day animal kingdom that influences the understanding of evolution and inspires today’s mechanical systems is only a fraction of all creatures that have existed through history.
Using fossil evidence to guide their design and a combination of 3D printed elements and polymers to mimic the flexible columnar structure of the moving appendage, the team demonstrated that pleurocystitids were likely able to move over the sea bottom by means of a muscular stem that pushed the animal forward.
Despite the absence of a current-day analog (echinoderms have since evolved to include modern-day starfish and sea urchins), pleurocystitids have been of interest to paleontologists due to their pivotal role in echinoderm evolution.
The team determined that wide sweeping movements were likely the most effective motion and that increasing the length of the stem significantly increased the animals’ speed without forcing it to exert more energy.
“Researchers in the bio-inspired robotics community need to pick and choose important features worth adopting from organisms,” explained Richard Desatnik, PhD candidate and co-first author.
“Essentially, we have to decide on good locomotion strategies to get our robots moving. For example, would a starfish robot really need to use 5 limbs for locomotion or can we find a better strategy?” added Zach Patterson, CMU alumnus and co-first author.
Now that the team has demonstrated that they can use Softbotics to engineer extinct organisms, they hope to explore other animals, like the first organism that could travel from sea to land – something that can’t be studied in the same way using conventional robot hardware.
“Bringing a new life to something that existed nearly 500 million years ago is exciting in and of itself, but what really excites us about this breakthrough is how much we will be able to learn from it,” said Phil LeDuc, co-author, and Professor of Mechanical Engineering at Carnegie Mellon University. “We aren’t just looking at fossils in the ground, we are trying to better understand life through working with amazing paleontologists.”
For more information: Proceedings of the National Academy of Sciences
Image: A pleurocystitid fossil and pleurocystitid robot replica. Credit: Carnegie Mellon University College of Engineering.
Probing the Intricate structures of 2D materials at the nanoscale
Two-dimensional (2D) materials are just a single or a few layers of atoms thick. These materials often have exotic properties that may be useful for next-generation technologies. When layers of these materials are stacked, the electronic properties that emerge can be manipulated by, for example, twisting the layers with respect to one another. To fully understand these properties and correlate them with the twist angle, scientists need advanced microscopy techniques. Researchers developed a novel operating mode for the interferometric four-dimensional scanning transmission electron microscopy (4D-STEM) technique. This special technique allows researchers to measure the atomic-scale structural distortions, twist angle, and interlayer spacings that influence the unique electronic properties of layered 2D materials.
Layered 2D materials have special properties that can advance technology beyond existing capabilities. For example, they could lead to faster and more energy-efficient computers or more reliable electricity storage. The individual layers that make up these materials may each be oriented differently. This creates challenges in fully understanding their 3D atomic structures with existing microscopy techniques. Interferometric 4D-STEM can reveal the relative positions of atoms within separate layers of stacked and twisted 2D materials. The technique opens avenues to the design and development of materials with useful properties.
Layered 2D materials have attracted considerable attention due to their interesting electronic properties, which can be modified by changing the twist angle of bilayer materials, the stacking sequence of trilayer materials, or other factors. To fully understand and control the properties of these materials, researchers need to study their atomic structures. However, visualizing the atomic structure of few-layered materials is often challenging using conventional microscopy techniques, such as when working with materials composed of light elements or when 3D information is needed. Researchers need new techniques to improve precision and locally measure distortions and interlayer spacings in twisted materials composed of two or three layers, especially when they contain light elements or high twist angles.
Researchers developed a new interferometric 4D-STEM modality that can provide information about local structural deformations within layers, twist direction and magnitude between layers, and interlayer distances for few-layered 2D materials. This new operating mode of 4D-STEM is still based on Bragg interferometry but uses a defocused electron probe to directly provide information about the relative positions of atoms within separate layers, as demonstrated in this study in bilayer and trilayer graphene. The technique sheds new light on the interplay between electronic properties and the precise structural arrangements of few-layer 2D materials.
For more information: U.S. Department of Energy Office of Scientific and Technical Information
Image: A convergent electron beam in a scanning transmission electron microscope interacts with a twisted bilayer of graphene (carbon), generating intricate disk-shaped intensity patterns that encode the precise local atomic arrangement.
Twisting two-dimensional atomic sheets: A key to new materials for advanced technologies
The way light interacts with naturally occurring materials is well-understood in physics and materials science. But in recent decades, researchers have fabricated metamaterials that interact with light in new ways that go beyond the physical limits imposed on naturally occurring materials.
A metamaterial is composed of arrays of “meta-atoms,” which have been fabricated into desirable structures on the scale of about a hundred nanometers. The structure of arrays of meta-atoms facilitate precise light-matter interactions. However, the large size of meta-atoms relative to regular atoms, which are smaller than a nanometer, has limited the performance of metamaterials for practical applications.
Now, a collaborative research team led by Bo Zhen of the University of Pennsylvania has unveiled a new approach that directly engineers atomic structures of material by stacking the two-dimensional arrays in spiral formations to tap into novel light-matter interaction. This approach enables metamaterials to overcome the current technical limitations and paves the way for next-generation lasers, imaging, and quantum technologies.
“It’s similar to stacking a deck of cards but twisting each card slightly before adding it to the pile,” says Zhen, a senior author of the paper and an assistant professor in the School of Arts & Sciences at Penn. “This twist changes how the entire ‘deck’ responds to light, enabling it to exhibit new properties that individual layers, or traditional stacks, do not possess.”
Bumho Kim, postdoctoral researcher in the Zhen Lab and first author of the paper, explains that by stacking layers of a material called tungsten disulfide (WS2) and twisting them at certain angles, they introduced what’s known as screw symmetries.
“The magic lies in controlling the twist,” Kim explains. “When you twist the layers at specific angles, you change the symmetry of the stack. Symmetry, in this context, refers to how certain properties of materials—like how they interact with light—are constrained by their spatial arrangement.”
By tweaking this arrangement at the atomic scale, the researchers have bent the rules of what these materials can do, and by controlling the twist across multiple layers of WS2, they created what’s known as 3D nonlinear optical materials.
Kim explains that a single layer of WS2 has particular symmetries, which allow certain types of interactions with light, where two photons at a given frequency can interact with the material to produce a new photon at double the frequency, a process known as second-harmonic generation (SHG).
“But, when two layers of WS2 are stacked with a twist angle different from the conventional 0° or 180°, all the mirror symmetries that were present in the single layer are broken,” says Kim. “This broken mirror symmetry is crucial because it leads to a chiral response—something entirely new and not seen in the individual layers.”
The researchers explain that the chiral response is significant because it is a cooperative effect resulting from the coupling between the electronic wavefunctions of the two layers, a phenomenon that can only arise in twisted interfaces.
An interesting property, Zhen adds, is that the sign of the chiral nonlinear response flips when the twist angle is reversed. This demonstrates direct control over the nonlinear properties by simply changing the twist angle between layers—a level of tunability that could be revolutionary for designing optical materials with custom responses.
Moving from bilayers to trilayers and beyond, the researchers observed how the interfacial SHG responses can constructively or destructively interfere depending on the twist angles between the layers.
In a stack with layers in multiples of four, “the chiral responses from all interfaces add up, while the in-plane responses cancel out,” says Kim. “This leads to a new material that exhibits only chiral nonlinear susceptibilities. This result could not be achieved without the precise stacking and twisting of the layers.”
The researchers found that screw symmetry enables new selectivity for the light’s electric field in the material, a part of light that determines its direction and intensity Kim notes how they found that screw symmetry enables a new kind of light generation in twisted four- and eight-layer stacks, counter-circularly polarized third harmonic generation, wherein light travels in the opposite spiral direction—a quality not seen in constituent WS2 monolayers.
“Adding an artificial screw symmetry allows us to control nonlinear optical circular selectivity at the nanoscale,” Kim says.
In testing this technique experimentally, the researchers verified the predicted nonlinearities inherent in various configurations of twisted WS2 stacks. The team observed new nonlinear responses and circular selectivity in twisted WS2 stacks that cannot be found in naturally occurring WS2, a revelation that could have profound implications in the field of nonlinear optics.
For more information: Nature Photonics
Understanding battery thermal runaway propagation
As the energy density of battery packs for vehicles and grid energy storage increases, how can we make high-density energy systems less hazardous and more reliable? That’s the question explored by scientists at Exponent Inc., Menlo Park, Calif.
Their new technical paper, “Understanding the Fundamental Mechanisms of Battery Thermal Runaway Propagation and Mitigation” published by the Society of Automotive Engineers, explains how severe thermal runaway scenarios can occur and outlines the tenets of successful mitigation to reduce these hazards.
Thermal runaway events often begin with the failure of a single battery cell or group of cells, cascading to other neighboring cells, and increasing in severity as the stored energy of the battery pack is released. To reduce the likelihood and severity of these scenarios, the scientists discuss design strategies that can impede propagation of thermal runaway events between cells.
To implement these design strategies and moderation measures, the authors suggest that design engineers first develop a deep understanding of the mechanisms that drive battery thermal runaway propagation. To start, the authors outline a number of the factors that drive many cell failures and runaway events such as acute exposure of a cell to high temperatures, mechanical abuse, and flaws in the construction of either individual cells or the battery pack.
The paper then discusses the mechanisms by which thermal runaway propagation can occur between cells and provides details on the fundamentals of these methods. In addition, the authors provide an overview of potential mitigation approaches to prevent thermal runaway propagation that are currently used in industry and commentary on pathways for developing an effective protection strategy.
For more information:
Exponent, Inc.































